Imaging Components, Systems, and Processing

Fusing multifocus images for yarn hairiness measurement

[+] Author Affiliations
Rongwu Wang

Donghua University, College of Textiles, 2999 North Renmin Road, Songjiang District, Shanghai 201620, China

Jinfeng Zhou, Lingjie Yu

Donghua University, College of Textiles, 2999 North Renmin Road, Songjiang District, Shanghai 201620, China

Bugao Xu

Donghua University, College of Textiles, 2999 North Renmin Road, Songjiang District, Shanghai 201620, China

University of Texas at Austin, Department of Human Ecology, 1363 The High Road, Austin, Texas 78712, United States

Opt. Eng. 53(12), 123101 (Dec 02, 2014). doi:10.1117/1.OE.53.12.123101
History: Received July 4, 2014; Accepted October 17, 2014
Text Size: A A A

Open Access Open Access

Abstract.  Yarn hairiness has been an important indication of yarn quality that affects weaving production and fabric appearance. In addition to many dedicated instruments, various image analysis systems have been adopted to measure yarn hairiness for potential values of high accuracy and low cost. However, there is a common problem in acquiring yarn images; that is, hairy fibers protruding beyond the depth of field of the imaging system cannot be fully focused. Fuzzy fibers in the image inevitably introduce errors to the hairiness data. This paper presents a project that attempts to solve the off-focus problem of hairy fibers by applying a new imaging scheme—multifocus image fusion. This new scheme uses compensatory information in sequential images taken at the same position but different depths to construct a new image whose pixels have the highest sharpness among the sequential images. The fused image possesses clearer fiber edges, permitting more complete fiber segmentation and tracing. In the experiments, we used six yarns of different fiber contents and spinning methods to compare the hairiness measurements from the fused images with those from unfused images and from the Uster tester.

Figures in this Article

Yarn hairiness refers to the number of fibers protruding outside the yarn core, which has a direct effect on yarn properties, weaving efficiency, and fabric appearance.1 Fiber properties (e.g., fiber length), spinning preparations (e.g., ring spinning), and spinning conditions (e.g., temperature) are the key factors that influence the severity of yarn hairiness. As an important indicator, the index of yarn hairiness has been included in yarn quality requirements. Despite the importance, yarn hairiness has not been used in yarn quality evaluations as widely as other properties, such as yarn strength and fineness, partly because it is more difficult to accurately measure.2

Since the 1950s, many different methods have been developed to measure hairiness.3 These measuring methods include appearance comparison, microscopy, singeing, electrical, and optical detections. In the method of yarn appearance, the inspectors used their naked eyes to observe the yarn and determined a hairiness level in reference to the control board.3 Pilay4 examined the yarn under the microscope and traced hairy fibers using a curve measuring instrument. Boswell and Townend5 estimated the total weight of the hairy fibers by contrasting the weight change before and after singeing the yarn. The singeing method has a shortcoming because it is difficult to control the timing so that only free fiber ends are burnt without damaging the yarn core. In the past several decades, electrical and optical methods became the dominant way for yarn hairiness measurements in two basic types—projection counting and a full feather photoelectric test. The latter is also called the diffuse reflectance method.6 The Germany Zweigle G566,7 China Chang ling YG172L,8 Japan Keisokki Laserspot Lst-III are examples of instruments based on projection counting. The yarn was projected into a plane and a light activated triode was placed at a monitoring point which was set at a certain distance, L, from the yarn core. When the yarn passed by the monitoring point, hairy fibers whose lengths were more than L blocked the light, causing the triode to generate electrical pulses. The yarn hairiness was measured by counting the pulses. In the full feather photoelectric method as applied in the Switzerland Uster tester,7 a monochrome light source was collimated through a convex lens to irradiate the yarn. In accordance with the change of light flux, the signals of yarn hairiness could be acquired.9 As shown in Fig. 1, there is a common drawback in the principle of the photoelectric approach, that is, the instruments can only perceive the projected lengths of protruding fibers in the two-dimensional plane, which distorts the hairiness data.10

Graphic Jump LocationF1 :

Principles of the optical hairiness instrument.

Since the late 1990s, the method for yarn hairiness measurement has been advanced by adopting image processing technology,11 which allows individual fibers to be directly examined. Cybulska12 developed special methods to estimate the external structure of yarns and to provide both global and local numeric characteristics of hairiness and twist. Kuzanski and Jackowska-Strumiłło.13 presented the edge-detection algorithm for measuring the real setting of the length and the number of the protruding fibers. Carvalho et al.14 use the Lab VIEW platform to develop a custom-made application that automatically determines yarn hairiness. Zhang15 captured images of a yarn placed on the black velvet board and processed the images with gray transformation, tilt correction, denoising, and edge sharpening. With the use of morphological operations, the characteristic parameters of yarn hairiness such as yarn perimeter, yarn area, and shape, could be calculated. Guha et al.16 developed an algorithm capable of analyzing yarn images taken under varying lighting conditions and varying yarn positions, and defined a new hairiness index to replace the traditional hairiness indicators. Fabijanska et al.17 adopted new image analysis algorithms to process yarn images, such as the graph cut method for yarn core extraction and high pass filtering for fiber extraction. They also proposed two new measures, hair area index and hair length index, to quantify yarn hairiness. Since tracing hairy fibers require the yarn to be observed under a microscope, the imaging system used to acquire a yarn image often has a limited depth of field (DOF) because of high magnification (e.g., 100×). Protruding fibers beyond the DOF will be defocused and blurry in the image. If the fibers are directly extracted and traced with the known algorithms, their true lengths are often mistakenly calculated, introducing errors to the hairiness data. Thus, coping with fuzzy curly fibers in the yarn image is the common problem in developing effective image processing algorithms for hairiness measurement.

This paper is aimed at solving the off-focus problem of hairy fibers in a yarn image by using an imaging scheme—multifocus image fusion. Since the 1950s, image fusion concepts and methods have been developed and applied in a wide range of fields,18 such as remote sensing, photogrammetry, medical imagery, feature extraction, object recognition, and so on. Multifocus image fusion is one of the fusion methods that uses a set of images of the same scene captured at various focal planes of a camera to construct a clear and shape image in which all objects are focused.19 Multifocus images comprise complementary information that can be seamlessly merged into one image more suitable for microscopic analysis of material properties, and they have been successfully used as accurate measurments of fiber diameters which could improve the fiber measurement accuracy by more than 20%20 for nonwoven structures with respect to the fiber orientation in the nonwoven fiber.21 In this new application for yarn hairiness measurement, the yarn passing through the microscope is intermittently advanced, and at each stop the yarn segment is imaged multiple times on different focal planes. The sequential images of the same view, called multifocus images, contain different sharp portions of curving fibers, which are compensatory in constructing a fused image. The new fused image consists of the sharpest pixels selected from various multifocus images, and permits more accurate image segmentation, which is fundamental to true measurements of fiber lengths sticking out of the yarn core. This paper will first introduce the acquisition method of multifocus images of yarn, briefly describe the algorithms of image fusion, segmentation and integration, and finally present the experiment results of six different yarns and the comparisons with the Uster measurements.

The yarn hairiness measurement system we developed in this project involved capturing microscopic images, multifocus image fusion and other processing algorithms, and modified hairiness indices.

Capturing Yarn Images

In this study, we utilized an optical microscope (M318, BEION, Shanghai) to obtain images of yarns unwrapped from a bobbin. A driving device was installed to control the movement of the microscope platform along the x-y axis direction that could move the yarn through the microscope.20 The power of magnification of the objective lens was set at 4×. A digital camera (C200, BEION) was mounted on the top of the microscope to capture images with a size of 800×600pixels, which approximately covered an actual area of 1×0.75mm2 on the yarn surface. According to the definition of the yarn hairiness index (H)-a total fiber length relative to the measurement field length of 1 cm,22 the measured yarn needs to be divided into 1-cm sections for the H calculation. Therefore, the yarn sample was forwarded 10 times at a 1-mm interval to yield the measurements in 1-cm sections. At each stop, 10 images were grabbed at different depths of view by adjusting the z-axis of the microscope,20 and then were fused into one sharp image where the protruding fibers were all well focused. Figure 2 shows two example images of a polyester yarn with hairy fibers protruding from the yarn core captured at different focal points. Figure 2(a) is the image taken in a closer view than Fig. 2(b), demonstrating that different partially focused images possess compensatory information for constructing a fully focused image.

Graphic Jump LocationF2 :

Microscopic images of a polyester yarn with hairy fibers protruding from the yarn core-taken image (a) in a closer view than image (b).

Image Fusion

Image fusion is a process to integrate information from multiple images to alleviate the multifocal problem of microscopic imaging. We employed a point-based image fusion algorithm to fuse multifocus images of fibers.21 Multifocus images refer to a series of images of the same view focused at different depths. Each multifocus image represents one image layer at which the image is only partially focused due to the limited DOF of the microscope. The magnitude of the intensity gradient at a pixel is often regarded as a measure of the sharpness of the pixel. Let N denote the number of image layers. The magnitudes of image gradients in each image layer are calculated, and the image gradients at the same coordinate among different image layers are compared. A matrix can be constructed by filling each element with the number of the image layer on which the image gradient has the largest value among all the layers. Through this gradient selection, the information extracted pixel by pixel from the multifocus images composes a new image whose pixels have the highest sharpness values among all the image layers. The new image is called the fused image. Figure 3 displays the fused image of the multifocus images of the polyester yarn in Fig. 2. The circles in the image marked a fiber end after the image fusion where the fuzzy fiber becomes sharply focused. The fused image warrants more complete detection of fringe fibers in the following process.

Graphic Jump LocationF3 :

Fused image of the multifocus images of the polyester yarn in Fig. 2.

Image Segmentation

Image segmentation is the process of extracting the regions of interest out of the image background. When the intensity distributions of objects and background pixels are sufficiently distinct, it is suitable to use a single threshold to segment an image. However, how to determine a threshold suitable for the entire image is always a challenge. An iterative algorithm17 capable of automatically estimating the threshold was adopted in the project. This image segmentation algorithm is described as follows:

  1. Select an initial estimate for the global threshold, T, as T=(Max+Min)/2. Here, Max and Min represent the maximum and minimum intensities of an entire image, respectively.
  2. Segment the image using T to produce two groups of pixels whose intensities are either above or below T. Calculate the average intensities, f1 and f2, for the two groups.
  3. Update the threshold as follows: T=(f1+f2)/2.
  4. Repeat steps 2 through 4 until the difference between the updated value and the previous value of T is smaller than a given tolerance ΔT. ΔT was selected as 0.05 in this study.

Figure 4 shows the polyester yarn in Fig. 3 after the image segmentation. The fuzzy fiber in the multifocus image [Fig. 2(a)] was missed in the image segmentation [Fig. 4(a)] because of its low contrast to the background. Having been enhanced via the image fusion, that fiber was fully segmented from the background as shown in Fig. 4(b).

Graphic Jump LocationF4 :

Binary images of the polyester yarn without (a) and with (b) image fusion.

Image Integration

As explained in the previous section, the successive images of a yarn need to be integrated together to form 1-cm long sections for hairiness measurement. We performed the morphological erosion23 on the binary image to remove thin hairy fibers, and then the skeletonization to extract the middle axis of the yarn core.23 The middle axes in the separate images were the reference lines for the integration. The reference lines from 10 images were successively linked, and finally the yarn segment with length of 1 cm could be formed. Figure 5(a) displays the integrated image with 10 original images on the same location under the microscope which contain the clear and blurred areas of yarn hairiness. As shown in Fig. 5(c), the same fibers falling into adjacent images are perfectly connected and there are no missing fibers as seen in Fig. 5(b). In the literature,12 Cybulska divided the yarn into two basis elements—the yarn core and hairiness according to compact agglomeration and mechanical properties. In this paper, in order to obtain the information about the yarn hairiness, with the progress of the integration, the orientation of the yarn core in each image needs to be identified. The morphological opening, that is, consecutive erosion and dilation, can remove thin objects such as hairy fibers and retain thick objects such as the yarn core. Figure 5(d) shows the separated yarn core and protruding fibers which are marked in red and green, respectively. From Fig. 5(d), which represents a 1-cm yarn segment, we can measure the areas of the yarn core (S1), and the yarn hairiness area (S2) and the total hairiness length (L) of the protruding fibers. Then, we can calculate the hairiness area ratio (A) and the hairiness value (H). A is defined as the ratio of the area of the protruding fibers divided by the total area of the yarn within the 1-cm segment, i.e., A=S2/(S1+S2). H refers to the total length of the protruding fibers on the 1-cm segment, that is, H is equal to L in cm.

Graphic Jump LocationF5 :

1-cm yarn sections assembled from 10 successive images (a), binary images without (b) and with image fusion (c), and separation of protruding fibers from the yarn core (d).

Table 1 shows the specifications of the six yarns, which were made of polyester, viscose rayon, cotton and their blends, and spun with ring, siro, rotor, and compact spinning machines, respectively. In this experiment, the yarn hairiness measurements were achieved via three methods: (1) image processing without multifocus image fusion, (2) image processing with multifocus image fusion, and (3) the Uster tester. Since the image processing system was not fully automated, particularly in the yarn advancing device, and the yarn had to remain stationary for the acquisition of sequential images, we were only able to capture and analyze approximately 10 consecutive images in 1 min, that is, one 1-cm yarn segments per minute. Therefore, we measured one 1-cm segment each meter for a total length of 10-m yarns per sample, and calculated the yarn core diameter, hairiness area ratio (A), and hairiness value (H). On the other hand, the Uster tester processed 1000-m yarns per sample at a speed of 400m/min with an H output.

Table Grahic Jump Location
Table 1Specifications of test yarns.

Figure 6 shows the comparisons of the total areas (S=S1+S2) and the areas (S1) of yarn cores of the six yarns. It can be seen that the S of a fused image is larger than that of the corresponding image without fusion, whereas S1 (yarn core) exhibits an opposite trend in that the S1s of the fused images are slightly lower than those of the unfused images. This is because in the fused image, hairy fibers are more complete and the edges of the yarn core are sharper than those in the unfused counterpart.

Graphic Jump LocationF6 :

Area comparisons of yarns and yarn cores with and without image fusion.

Tables 20034 provide the averages and the standard deviations of the three yarn measurements (D, A, and H) for the 10 samples of each yarn, and the Pearson correlation coefficients24 of these measurements from the unfused and fused images. From Table 2, it was clear that the diameters (D) of the yarn cores became 2 to 5μm thinner after the image fusion, which was consistent with the change in the S1. However, the two sets of diameter data in each yarn were highly correlated with the minimal R being 0.982 for yarn 4 and the maximal R being 0.999 for yarn 5. In Table 3, the hairiness area ratios (A) increased by 4% to 10% among the six yarns after applying the image fusion to the process. The standard deviations (SDs) of the A measurements from the fused images also seemed to be higher than those from the unfused images. The two sets of A measurements had fairly high Rs (from 0.834 to 0.992). In Table 4, the H measurements increased roughly 0.5 to 1.1 units after applying the image fusion technique, meaning that approximately a total of 1 cm more hairy fibers were detected per 1-cm yarn segment. But the correlations in H between the fused and unfused images ranged from 0.884 (yarn 3) to 0.974 (yarn 5). The H SDs of the six yarns were also slightly increased in the fused images.

Table Grahic Jump Location
Table 2Average diameters (D) of yarn cores with the image system.
Table Grahic Jump Location
Table 3Measurements of hairiness area ratios (A) with the image system.
Table Grahic Jump Location
Table 4Measurement of hairiness value (H) with the image system.

In order to verify whether or not the mean values of the yarn data from the two image processing methods (fusion or no fusion) are significantly different, the t-test was performed as reported in Tables 50067. Since the t-test requires the data to obey the normal distributions and to have a homogeneity of variances, we chose the Shapiro–Wilk test25 and the F-test26 to verify the normality and the homogeneity of the variances of the data. In the Shapiro–Wilk test, all the test statistic values (W) of the three measurements (D, A, and H) of the six yarns were larger than the critical value Z=0.781 at the significant level α=0.01. Therefore, these data satisfied the normality requirement. In the F-test, the degree of freedom was 9 (df=n1=9). The test statistic values of the three measurements (D, A, and H) of the six yarns with the methods of image processing system were below the critical value F(9,9)=2.98 at the significant level α=0.05. Thus, there was no significant difference in variances under the possibility of 95%, that is, the samples data conformed to the homogeneity of variances. Since the data of the two image processing methods (with and without image fusion) were collected from the same sets of images, the paired t-tests27 were suitable. In this case, the degree of freedom was 9 and the critical value was 2.262 for the two-tailed test (α=0.05). From Tables 50067, the t-statistic values of the six yarns were all above 2.262. Therefore, the null hypothesis was rejected, i.e., the mean values of the yarn core diameters, hairiness area ratios and hairiness values of the paired two samples from the fused images, and the unfused images were statistically different. As demonstrated in Fig. 5, the multifocus image fusion technique enhanced the quality of yarn images, permitting more complete detections of hairy fibers which led to significant increases in the yarn hairiness measurements.

Table Grahic Jump Location
Table 5Statistic analysis of yarn core diameters (D).
Table Grahic Jump Location
Table 6Statistic analysis of hairiness area ratios (A).
Table Grahic Jump Location
Table 7Statistic analysis of hairiness values (H).

The hairiness values of the six yarns were also measured by using a Uster Tester (Table 8). Each yarn was tested 10 times for a length of 1000 m/test and at a speed of 400m/min. Compared with the image fusion system (Table 4), the Uster tester outputted much lower H values, which suggested that the Uster tester could underestimate yarn hairiness because of the drawback pointed out in the introduction. Of course, this discrepancy also arose from the difference in the test conditions (sampling rate, speed, air-drag, etc.,) of the two systems. The image fusion system measured a shorter length, operated at a lower speed and kept hairy fibers in more natural positions than the Uster tester did. This also explained the reason why the correlation between the two sets of H data is fairly low. Through the Shapiro–Wilk test,25 these data of Uster tester also satisfied the normality requirement; however, the F-test verified that there existed a significant difference between variances of yarn samples measured by the image fusion system and the Uster tester. In addition, since the H data of the same kind of yarn for the two methods were from different sections and under different testing conditions, the unpaired and unequal variance t-tests were performed to check if the mean values of the two H sets were significantly different. In this case, the degree of freedom in each yarn test was computed as follows:28Display Formula

df=(S12/n1+S22/n2)2(S12/n1)2n11+(S22/n2)2n21,
where S1 and S2 were the variances of each yarn sample with the image fusion system and Uster tester, and n1 and n2 are the numbers of detected yarn samples (both n1 and n2 were 10 in this experiment). It was found that the df of yarn 5 was 10 (the SD of yarn 5 is lower than that of the rest, so the calculated value is 9.84, rounding down to 10) and the dfs of the remainder of the yarns were 9. At the significant level α=0.05, the critical T values are 2.228 at df=10 and 2.262 at df=9. The t-statistic data in Table 8 were all above their critical values. Thus, the null hypothesis was rejected. These two sets of H data significantly differed in their mean values.

Table Grahic Jump Location
Table 8Hairiness values from Uster tester and comparisons with the image system.

This paper presented a new measurement for yarn hairiness with image processing method based on the multifocus image fusion technique. Because hairy fibers on the yarn core can easily extend outside of the DOF of the imaging system, they cannot be fully focused in one image. Therefore, the hairiness measurements are often underestimated due to missing fibers in the image. We used a microscope that is focusable at various depths to capture a series of partially focused images at each examining position, and a pixel-based image fusion algorithm to merge sharp pixels selected from the image series to form a well-focused image. In the fused image, hairy fibers protruding in different directions and lengths all become sharp and complete, which warrants more accurate segmentation of the fibers from the background. We chose six yarns of different fiber contents and spinning methods and the measured yarn hairiness with three methods: image processing system without image fusion (1) and with image fusion (2) and the Uster tester (3) for the comparison tests. Through the paired t-tests, it was found that the hairiness area ratios (A) and the hairiness values (H) with image fusion were significantly higher than those without image fusion. Therefore, we attested that the application of the image fusion technique could yield more yarn hairiness information. The yarn hairiness values from the Uster tester were less than the H values from the image processing system, and the two sets H values had low correlation coefficients and significantly different means according to the t-test results. This preliminary test suggests that the Uster tester could underestimate yarn hairiness because of the drawback of the used photoelectric approach. The presented image fusion technique appears to be an effective way to correct the measurement of yarn hairiness in current image analysis or other photoelectric systems.

This research was supported by the Natural Science Foundation of China (Grant No. 61172119), the Fundamental Research Funds for the Central Universities, China, the Foundation for the Author of National Excellent Doctoral Dissertation of PR China (Grant No. 201168), and Program for New Century Excellent Talents in University (Grant No. NCET-12-0825).

Qin  Z., Chen  Y., “The overview of yarn hairiness testing methods,” Wool Technol. J.. 4, , 48 –51 (1999). 0372-7459 
Chauhan  R. S., “Yarn hairiness: measurement, effect and consequences,” Indian Text. J.. 119, (5 ), 36 –43 (2009). 0019-6436 
Barella  A., Yarn Hairiness. ,  Textile Institute ,  Manchester, England  (1983).
Pillay  K. P. R., “A study of yarn hairiness in cotton yarns: part I, effect of fiber and yarn factors,” Text. Res. J.. 34, , 663  (1964). 0040-5175 CrossRef
Boswell  H. R., Townend  P. P., “Some factors affecting the hairiness of worsted yarns,” Text. Inst. J.. 48, , T135  (1957). 0040-5000 
Le  F., Zhang  D., “The performance of the two kinds of hairiness tester,” Cotton Text. Technol. J.. 4, (38 ), 268  (2010).
Guo  H., Wang  J., “Analyzing several hairiness testing methods,” Heibei Text. J.. 3, , 75 –80 (2007).
Xie  L., Jiao  A., “Properties and the application of the yarn hairiness tester YG17IL,” in  Proc. National Modern Spinning Technology Seminar R ,  China , pp. 69 –77 (2010).
Uster Technologies AG, Uster Statistics Application Handbook. ,  Uster Technologies Ltd. ,  Switzerland  (2013).
Brunk  N., “Methods of testing yarn hairiness,” Africa Mid. East Text.. 1, , 20 –20 (2005).
Kuzariski  M., “Measurement methods for yarn hairiness analysis—the idea and construction of research standing,”  in Proc. of the 2nd Int. Conf. on Perspective Technologies and Methods in MEMS Design (MEMSTECH 2006) ,  Lviv-Polyana, Ukraine , pp. 87 –90(2006).
Cybulska  M., “Assessing yarn structure with image analysis methods,” Text. Res. J.. 69, (5 ), 369 –373 (1999). 0040-5175 CrossRef
Kuzanski  M., Jackowska-Strumiłło  L., “Yarn hairiness determination the algorithms of computer measurement methods,” in  Proc. IEEE Int. Conf. on Perspective Technologies and Methods in MEMS Design , pp. 154 –157,  Lviv-Polyana, Ukraine  (2007).
Carvalho  V. et al., “Yarn hairiness determination using image processing techniques,” in  Proc. IEEE Int. 16th Conf. on Emerging Technologies and Factory Automation (ETFA) ,  Toulouse, France  (2011).
Zhang  J., “Application study on the yarn hairiness detection based on image processing technology,” Thesis, Hebei Univ. of Science and Technology (2011).
Guha  A. et al., “Measurement of yarn hairiness by digital image processing,” J. Text. Inst.. 101, (3 ), 214 –222 (2010). 0040-5000 CrossRef
Fabijanska  A., Jackowska-Strumiłło  L., “Image processing and analysis algorithms for yarn hairiness determination,” Mach. Vis. Appl.. 23, , 527 –540 (2012). 0932-8092 CrossRef
Wang  Z. et al., “A comparative analysis of image fusion methods,” IEEE Trans. Geosci. Remote Sens.. 43, (6 ), 1391 –1402 (2005). 0196-2892 CrossRef
De  I., Chanda  B., “A simple and efficient algorithm for multifocus image fusion using morphological wavelets,” Signal Process.. 86, , 924 –936 (2006). 0165-1684 CrossRef
Wang  R. et al., “Multi-focus image fusion for enhancing fiber microscopic images,” Text. Res. J.. 82, (4 ), 352 –361 (2012). 0040-5175 CrossRef
Wang  R., Xu  B., Li  C., “Accurate fiber orientation measurements in nonwovens using multi-focus image fusion technique,” Text. Res. J.. 84, (2 ), 115 –124 (2014). 0040-5175 CrossRef
Richard  F., Textile Measuring Technology and Quality Control. , 1st ed.,  Donghua University Press ,  Shanghai, China  (2006).
Rafael  C. G., Richard  E. W., Digital Image Processing. , 3rd ed.,  Publishing House of Electronics Industry ,  Beijing  (2012).
Ahlgren  P., Jarneving  B., Rousseau  R., “Requirements for a cocitation similarity measure, with special reference to Pearson’s correlation coefficient,” J. Am. Soc. Inform. Sci. Technol.. 54, (6 ), 471 –592 (2003). 1532-2882 CrossRef
Patrick  R., “Approximating of Shapiro-Wilk W-test for non-normality,” Stat. Comput.. 2, , 117 –119 (1992). 0960-3174 CrossRef
Tjen-Sien  L., Wei-Yin  L., “A comparison of tests of equality of variances,” Comput. Stat. Data Anal.. 22, (3 ), 287 –301 (1996). 0167-9473 CrossRef
Daya  S., “Understanding statistics: paired t-test,” Evidence-Based Obstet. Gynecol.. 5, (13 ), 105 –106 (2003).
Ruxton  G. D., “The unequal variance t-test is an underused alternative to Student’s t-test and the Mann–Whitney U test,” Behav. Ecol.. 17, (4 ), 688 –690 (2006). 1045-2249 CrossRef

Rongwu Wang received his PhD degree from Donghua University at Shanghai, China, in 2008 and joined the faculty in the College of Textiles, Donghua University, after 2 years of postdoctoral research in the same university. Currently, he is an associate professor at the College of Textiles and conducts research on new applications of image processing and microimage recognition systems.

Biographies of the other authors are not available.

© The Authors. Published by SPIE under a Creative Commons Attribution 3.0 Unported License. Distribution or reproduction of this work in whole or in part requires full attribution of the original publication, including its DOI.

Citation

Rongwu Wang ; Jinfeng Zhou ; Lingjie Yu and Bugao Xu
"Fusing multifocus images for yarn hairiness measurement", Opt. Eng. 53(12), 123101 (Dec 02, 2014). ; http://dx.doi.org/10.1117/1.OE.53.12.123101


Figures

Graphic Jump LocationF1 :

Principles of the optical hairiness instrument.

Graphic Jump LocationF2 :

Microscopic images of a polyester yarn with hairy fibers protruding from the yarn core-taken image (a) in a closer view than image (b).

Graphic Jump LocationF3 :

Fused image of the multifocus images of the polyester yarn in Fig. 2.

Graphic Jump LocationF4 :

Binary images of the polyester yarn without (a) and with (b) image fusion.

Graphic Jump LocationF5 :

1-cm yarn sections assembled from 10 successive images (a), binary images without (b) and with image fusion (c), and separation of protruding fibers from the yarn core (d).

Graphic Jump LocationF6 :

Area comparisons of yarns and yarn cores with and without image fusion.

Tables

Table Grahic Jump Location
Table 1Specifications of test yarns.
Table Grahic Jump Location
Table 2Average diameters (D) of yarn cores with the image system.
Table Grahic Jump Location
Table 3Measurements of hairiness area ratios (A) with the image system.
Table Grahic Jump Location
Table 4Measurement of hairiness value (H) with the image system.
Table Grahic Jump Location
Table 5Statistic analysis of yarn core diameters (D).
Table Grahic Jump Location
Table 6Statistic analysis of hairiness area ratios (A).
Table Grahic Jump Location
Table 7Statistic analysis of hairiness values (H).
Table Grahic Jump Location
Table 8Hairiness values from Uster tester and comparisons with the image system.

References

Qin  Z., Chen  Y., “The overview of yarn hairiness testing methods,” Wool Technol. J.. 4, , 48 –51 (1999). 0372-7459 
Chauhan  R. S., “Yarn hairiness: measurement, effect and consequences,” Indian Text. J.. 119, (5 ), 36 –43 (2009). 0019-6436 
Barella  A., Yarn Hairiness. ,  Textile Institute ,  Manchester, England  (1983).
Pillay  K. P. R., “A study of yarn hairiness in cotton yarns: part I, effect of fiber and yarn factors,” Text. Res. J.. 34, , 663  (1964). 0040-5175 CrossRef
Boswell  H. R., Townend  P. P., “Some factors affecting the hairiness of worsted yarns,” Text. Inst. J.. 48, , T135  (1957). 0040-5000 
Le  F., Zhang  D., “The performance of the two kinds of hairiness tester,” Cotton Text. Technol. J.. 4, (38 ), 268  (2010).
Guo  H., Wang  J., “Analyzing several hairiness testing methods,” Heibei Text. J.. 3, , 75 –80 (2007).
Xie  L., Jiao  A., “Properties and the application of the yarn hairiness tester YG17IL,” in  Proc. National Modern Spinning Technology Seminar R ,  China , pp. 69 –77 (2010).
Uster Technologies AG, Uster Statistics Application Handbook. ,  Uster Technologies Ltd. ,  Switzerland  (2013).
Brunk  N., “Methods of testing yarn hairiness,” Africa Mid. East Text.. 1, , 20 –20 (2005).
Kuzariski  M., “Measurement methods for yarn hairiness analysis—the idea and construction of research standing,”  in Proc. of the 2nd Int. Conf. on Perspective Technologies and Methods in MEMS Design (MEMSTECH 2006) ,  Lviv-Polyana, Ukraine , pp. 87 –90(2006).
Cybulska  M., “Assessing yarn structure with image analysis methods,” Text. Res. J.. 69, (5 ), 369 –373 (1999). 0040-5175 CrossRef
Kuzanski  M., Jackowska-Strumiłło  L., “Yarn hairiness determination the algorithms of computer measurement methods,” in  Proc. IEEE Int. Conf. on Perspective Technologies and Methods in MEMS Design , pp. 154 –157,  Lviv-Polyana, Ukraine  (2007).
Carvalho  V. et al., “Yarn hairiness determination using image processing techniques,” in  Proc. IEEE Int. 16th Conf. on Emerging Technologies and Factory Automation (ETFA) ,  Toulouse, France  (2011).
Zhang  J., “Application study on the yarn hairiness detection based on image processing technology,” Thesis, Hebei Univ. of Science and Technology (2011).
Guha  A. et al., “Measurement of yarn hairiness by digital image processing,” J. Text. Inst.. 101, (3 ), 214 –222 (2010). 0040-5000 CrossRef
Fabijanska  A., Jackowska-Strumiłło  L., “Image processing and analysis algorithms for yarn hairiness determination,” Mach. Vis. Appl.. 23, , 527 –540 (2012). 0932-8092 CrossRef
Wang  Z. et al., “A comparative analysis of image fusion methods,” IEEE Trans. Geosci. Remote Sens.. 43, (6 ), 1391 –1402 (2005). 0196-2892 CrossRef
De  I., Chanda  B., “A simple and efficient algorithm for multifocus image fusion using morphological wavelets,” Signal Process.. 86, , 924 –936 (2006). 0165-1684 CrossRef
Wang  R. et al., “Multi-focus image fusion for enhancing fiber microscopic images,” Text. Res. J.. 82, (4 ), 352 –361 (2012). 0040-5175 CrossRef
Wang  R., Xu  B., Li  C., “Accurate fiber orientation measurements in nonwovens using multi-focus image fusion technique,” Text. Res. J.. 84, (2 ), 115 –124 (2014). 0040-5175 CrossRef
Richard  F., Textile Measuring Technology and Quality Control. , 1st ed.,  Donghua University Press ,  Shanghai, China  (2006).
Rafael  C. G., Richard  E. W., Digital Image Processing. , 3rd ed.,  Publishing House of Electronics Industry ,  Beijing  (2012).
Ahlgren  P., Jarneving  B., Rousseau  R., “Requirements for a cocitation similarity measure, with special reference to Pearson’s correlation coefficient,” J. Am. Soc. Inform. Sci. Technol.. 54, (6 ), 471 –592 (2003). 1532-2882 CrossRef
Patrick  R., “Approximating of Shapiro-Wilk W-test for non-normality,” Stat. Comput.. 2, , 117 –119 (1992). 0960-3174 CrossRef
Tjen-Sien  L., Wei-Yin  L., “A comparison of tests of equality of variances,” Comput. Stat. Data Anal.. 22, (3 ), 287 –301 (1996). 0167-9473 CrossRef
Daya  S., “Understanding statistics: paired t-test,” Evidence-Based Obstet. Gynecol.. 5, (13 ), 105 –106 (2003).
Ruxton  G. D., “The unequal variance t-test is an underused alternative to Student’s t-test and the Mann–Whitney U test,” Behav. Ecol.. 17, (4 ), 688 –690 (2006). 1045-2249 CrossRef

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging & repositioning the boxes below.

Related Book Chapters

Topic Collections

PubMed Articles
Advertisement
  • Don't have an account?
  • Subscribe to the SPIE Digital Library
  • Create a FREE account to sign up for Digital Library content alerts and gain access to institutional subscriptions remotely.
Access This Article
Sign in or Create a personal account to Buy this article ($20 for members, $25 for non-members).
Access This Proceeding
Sign in or Create a personal account to Buy this article ($15 for members, $18 for non-members).
Access This Chapter

Access to SPIE eBooks is limited to subscribing institutions and is not available as part of a personal subscription. Print or electronic versions of individual SPIE books may be purchased via SPIE.org.