Instrumentation, Techniques, and Measurement

Optical beat-note frequency stabilization between two lasers using a radio frequency interferometer in the gigahertz frequency band

[+] Author Affiliations
Tomoyuki Uehara

National Defense Academy of Japan, Department of Communications Engineering, Hashirimizu 1-10-20, Yokosuka-shi, Kanagawa-Pref 239-8686, Japan

Kenichiro Tsuji

National Defense Academy of Japan, Department of Communications Engineering, Hashirimizu 1-10-20, Yokosuka-shi, Kanagawa-Pref 239-8686, Japan

Kohei Hagiwara

National Defense Academy of Japan, Department of Communications Engineering, Hashirimizu 1-10-20, Yokosuka-shi, Kanagawa-Pref 239-8686, Japan

Noriaki Onodera

National Defense Academy of Japan, Department of Communications Engineering, Hashirimizu 1-10-20, Yokosuka-shi, Kanagawa-Pref 239-8686, Japan

Opt. Eng. 53(12), 124109 (Dec 29, 2014). doi:10.1117/1.OE.53.12.124109
History: Received August 3, 2014; Accepted November 20, 2014
Text Size: A A A

Open Access Open Access

Abstract.  A beat-note frequency stabilization system using a distributed-feedback laser and external cavity laser diode has become a very important technique for laser spectroscopy, where highly stabilized high-frequency beat notes are required. We have developed a simple and versatile system capable of stabilizing the high-frequency beat notes (3 to 11 GHz) of two lasers using a delayed radio frequency self-heterodyne interferometer and have confirmed its basic operation. The frequency stability of the obtained beat notes is higher than 1 MHz in the 3- to 11-GHz frequency range with an average time of 20 s.

Figures in this Article

Frequency-tunable and frequency-stable microwave sources are becoming increasingly important in the fields of measurement/spectroscopy and communications. Microwave signals are usually generated using complicated electronic circuits with multistep frequency multiplication to obtain the desired frequency signal. In contrast to the complicated conventional electronic method, optical generation of microwave signals using optical beat-note generation, i.e., optical heterodyning using two optical sources, with ultrafast photodetectors (PDs)1 can be performed with simple experimental apparatuses. However, since the frequency of the generated microwave signal directly corresponds to the frequency difference between the two optical sources, frequency fluctuation may arise if the optical sources are unstable. To generate stable microwave signals, the beat-note frequency of the two optical sources used for optical heterodyning must be stabilized. Optical phase-locked loop (OPLL) is a widely used method for beat-note frequency stabilization. In OPLL, the target signal frequency is locked to a stable reference frequency generated by a radio frequency (RF) synthesizer. Using this technique, two independent lasers can be offset locked in atomic spectroscopy.26 The OPLL is also used in ion optical clocks7,8 for quantum information processing, power combination of high-power lasers,9 and microwave photonics.1013 In previous studies, several other techniques have been used to obtain highly stable and low-phase noise beat notes such as two-mode optical cavity atomic resonances14 and injection locking schemes.8 The frequency stabilities of these systems are less than 1 Hz for the best performance, when the stable frequency reference (e.g., ultralow expansion glass optical cavity and ultrastable oscillator) is used. However, these systems require complicated circuits and/or special optical devices as required in OPLL and the locking range is narrow. The typical locking range of these systems is several megahertz.

Recently, technological developments in electronics have enabled simple frequency stabilization schemes in high-frequency regions suitable for photonic microwave generation.15,16 Recently developed circuits can generate microwaves at 810 MHz using a simple technique; however, they have not yet been used to generate a beat note in the gigahertz frequency region.

In this paper, we propose and demonstrate the photonic generation of stabilized microwave frequency signals ranging from 3 to 11 GHz using a loop filter with a delayed RF interferometer. The locking characteristics of the loop filter can be optimized with the help of the interferometer. As a result, compared with the previously reported systems, the frequency locking range of our system extends to several hundred megahertz, while a simpler operation is achieved in the proposed configuration. The frequency stability obtained in our system is higher than 1 MHz, which is sufficient for photonic RF signal generation (e.g., phased array antenna using photonic-generated RF signals1) or basic spectroscopic applications. Further improvement of frequency stability, i.e., higher than 10-kHz range stability, will be possible by using a narrow linewidth laser instead of the distributed-feedback laser used in our system.

A schematic for beat-note frequency stabilization is shown in Fig. 1. The purpose of this experiment is to demonstrate the stabilization of the beat note generated by two lasers (LD1 and LD2) to generate a highly stable synthesizer signal. An RF self-heterodyne interferometer is introduced to control the locking characteristics of the servo loop. An error signal proportional to the frequency difference between the beat- and RF synthesizer-signals is converted to a DC signal and applied to LD2 to control its frequency.

Graphic Jump LocationF1 :

Schematic of beat-note frequency stabilization by means of a radio frequency (RF) self-homodyne interferometer. PD: photodetector; LPF: low pass filter.

The RF signal intensity, I, generated by PD, is proportional to the intensity of the incident light and can be expressed as Display Formula

I|E1cos(ω1t)+E2cos(ω2t)|2=E12cos2(ω1t)+E22cos2(ω2t)+2E1E2cos(ω1t)cos(ω2t),(1)
where E1 and E2 are the amplitudes of the electric fields of the two beams of light with frequencies ω1 and ω2, respectively. By eliminating the DC components in Eq. (1), an RF signal component from the PD, IRF, can be obtained as Display Formula
IRF2E1E2cos(ω1t)cos(ω2t)=E1E2·{cos[(ω1ω2)·t]+cos[(ω1+ω2)·t]}(2)
Display Formula
E1E2·{cos[(ω1ω2)·t]}.(3)

Since the second term in Eq. (2) represents the higher frequency component and is outside the PD bandwidth, the component cannot be detected by the PD. Thus, only the low-frequency component [i.e., Eq. (3)] can be observed. In the following discussion, |ω1ω2| is expressed as Δω and corresponds to the beat-note frequency.

To stabilize the beat-note frequency to a reference frequency of the synthesizer, the synthesizer signal with frequency ωSynth is multiplied by the beat signal using a frequency mixer. As a consequence of the multiplication, oscillating signals with two frequency components are generated, as indicated in Eq. (4). Because the frequency component Δω+ωSynth is higher than the cut-off frequency of Mixer1, we can use the last term [Eq. (5)], which is proportional to ΔωωSynth, to obtain an error signal Display Formula

cos(Δω·t)·cos(ωSynth·t)=12{cos[(ΔωωSynth)·t]+cos[(Δω+ωSynth)·t]}(4)
Display Formula
12{cos[(ΔωωSynth)t]}.(5)

The signal proportional to ΔωωSynth is transformed into a DC signal for frequency stabilization used in the feedback loop. This is done by splitting the signal with ΔωωSynth frequency into two equal components and multiplying them by Mixer2 (bandwidth: 200 MHz), while one signal passes through an additional delay line. A coaxial cable is used as a delay line to create a delay time τ (5 ns for a 1-m cable) between the two signals. The delay time τ is equivalent to a phase shift ϕ of τ·(ΔωωSynth). The output signal S from Mixer2 is Display Formula

Scos[(ΔωωSynth)·t]·cos[(ΔωωSynth)·t+ϕ]=12{cosϕ+cos[2(ΔωωSynth)·t+ϕ]}.(6)

Equation (6) consists of a DC part proportional to the phase shift and an AC part, which can be filtered out by a low pass filter (LPF). As a result, the error signal is obtained as Display Formula

Scosϕ=cos[τ·(ΔωωSynth)].(7)

By scanning the frequency of LD1 or LD2 (i.e., changing Δω), the error signal traces a cosine curve with a finite width corresponding to the bandwidth of Mixer2. The error signal has several zero crossing points, and one of these points is used as a locking point. The neighboring locking points are separated by 2π/τ. By changing the cable length l of the delay line, the locking points and the slope at the zero crossing points can be changed. The locking bandwidth is given by approximately 2π/τ, so a shorter delay line gives a wider locking bandwidth and lower discrimination gain (i.e., derivative of the error signal at the zero crossing point), and vice versa.

The experimental setup of the photonic generation of an RF signal in the gigahertz region is shown in Fig. 2. An external cavity diode laser (ECL) and a distributed feedback (DFB) laser are used as optical sources to create an optical beat note. The ECL (Photonetics: TUNICS-PRI, linewidth: 0.5 MHz) is used for coarse tuning of the beat-note frequency, since its tuning range is wide (approximately 16 THz, corresponding to 1470 to 1599 nm). The DFB (Fitel: FRL15DCWx-A8x-W1510, linewidth: 3.3 MHz) laser is used for fine tuning of the beat frequency, together with the servo system, since its optical frequency can be controlled by an injection current. The optical output signals of the ECL and the DFB laser are combined by a 2×2 3-dB coupler. One of the output optical signals from the coupler is measured by an optical spectrum analyzer (Advantest, U3772). The beat note (the other output signal from the coupler) is detected by a fast (typically 40-GHz) photodiode (Picometrix, P-40HPA) and converted to an RF signal. The RF signal is amplified by RF amplifiers (Avantec, APT10566 and Anritsu, A3HB3102) to the range between 10 and +4dBm. The amplified signal is subsequently divided by a power splitter (Anritsu, K241C). One of the divided signals is measured by an RF spectrum analyzer or a sampling oscilloscope, while the other is mixed with the output of an RF synthesizer (Anritsu, MS9030A+MS9703) using a frequency mixer (Mini Circuits, ZX05-153+). The bandwidth of the mixer (3 to 15 GHz) is sufficient for photonic generation in the 10-GHz range. The signal, generated by mixing the beat note and RF synthesizer output, is split by a power splitter (Anritsu, K241C). One of the split signals is delayed by a coaxial cable (Hitachi Cable, MW3.00-FF-3000; length, 3 m) and multiplied by another split signal using a mixer (Mini Circuits, ZLW-3+, bandwidth: 200 MHz). The mixed signal is then amplified and used as an error signal for a feedback system. The residual RF component created by the down conversion process is eliminated by a 5-MHz LPF placed before the amplifier.

Graphic Jump LocationF2 :

Expermental setup. PD: photodetector; LPF: low pass filter.

Figure 3 shows the measured optical spectra of the ECL and DFB laser using an optical spectrum analyzer (Advantest, Q8384). The wavelengths of the ECL and DFB laser are 1549.18 and 1549.26 nm, respectively. Using an RF spectrum analyzer, the measured frequency of the generated beat note is obtained as 9.983 GHz, as shown in Fig. 4. The obtained beat-note frequency is consistent with the difference between the two optical frequencies of the ECL and DFB laser. When the frequency of the ECL is scanned over 1 GHz, the beat-note frequency is also swept together with the frequency of ECL. According to Eq. (7), this results in a cosine variation of the error signal.

Graphic Jump LocationF3 :

Optical spectrum of ECL and DFB laser.

Graphic Jump LocationF4 :

Beat note generated from the two lasers.

Figure 5 shows the measured results of the error signal as a function of ΔωωSynth using an oscilloscope. In the servo loop, one of the zero crossing points of the error signal is used to lock the frequency difference between the ECL and DFB laser. A proportional integral derivative servo (bandwidth: 10 kHz) is used to control the injection current of the DFB laser. When the servo loop is closed, the beat frequency spectrum becomes stable, as shown in Fig. 6. For comparison, a measured free running beat frequency spectrum is shown in Fig. 7. The drift of the beat frequency is estimated to be around 22 MHz. To investigate the effect of our stabilization method, the time-domain beat note is measured by a sampling oscilloscope.

Graphic Jump LocationF6 :

Beat note with frequency stabilization.

Graphic Jump LocationF7 :

Beat note without frequency stabilization.

Figures 8 and 9 show the measured sampling oscilloscope traces with frequency stabilization with 2-event averaging (Fig. 8) and 100-event averaging (Fig. 9). The sampling scope was self-triggered by a beat-note RF signal. In each figure, three traces are measured at 60-s intervals, three times. As shown in these figures, the three traces almost overlap, which is clear evidence that a stable beat signal has been successfully generated in our system. From these figures and the RF spectrum shown in Fig. 6, it can be concluded that the frequency noise of the beat note is reduced to almost the same level as the frequency noise of the RF synthesizer. The same measurements were then performed for the beat signal without frequency stabilization.

Graphic Jump LocationF8 :

Beat note with frequency stabilization measured by a sampling oscilloscope (2-event averaging).

Graphic Jump LocationF9 :

Beat note with frequency stabilization measured by a sampling oscilloscope (100-event averaging).

Figures 10 and 11 show the measured sampling scope traces of the beat signal without frequency stabilization, corresponding to Figs. 8 and 9, respectively. Compared with a beat note which is frequency stabilized to the RF synthesizer signal, the beat note without frequency stabilization shown in Figs. 10 and 11 has drifted. This can be explained as follows.

Graphic Jump LocationF10 :

Beat note without frequency stabilization measured by a sampling oscilloscope (2-event averaging).

Graphic Jump LocationF11 :

Beat note without frequency stabilization measured by a sampling oscilloscope (100-event averaging).

Without the frequency stabilization, the frequency of the ECL drifts, as shown in the beat-note RF spectrum (Fig. 7). In this situation, it is likely that the phase of the laser light shifts/jumps randomly over time. A simple mathematical calculation shows that the phase of the beat note is closely linked with the phase difference between the two optical sources used for the beat-note generation. Thus, when the phase of the RF beat signal changes because of the unstable optical phase of the laser light, the trigger timing may be changed for self-triggered oscilloscope measurements. This may be the reason for the drifting scope traces shown in Figs. 10 and 11.

The similarity between the frequency-stabilized beat notes from 3 to 11 GHz is shown in Fig. 12, and the frequency stability at 10-GHz RF synthesizer frequency is shown in Fig. 13. Frequency fluctuations observed in these beat notes are less than 1 MHz over an average time of 20 s and are currently limited by the linewidth of the DFB laser. The frequency stability of the beat note was also measured using an RF spectrum analyzer. The long-term stability is improved by 1/100 compared with the free running operation.

Graphic Jump LocationF12 :

Beat note between two lasers in frequency stabilization. RF synthesizer frequency set at (a) 3 GHz, (b) 4 GHz, (c) 5 GHz, (d) 6 GHz, (e) 7 GHz, (f) 8 GHz, (g) 9 GHz, (h) 10 GHz, and (i) 11 GHz.

Graphic Jump LocationF13 :

Frequency stability of generated beat note at 10-GHz RF synthesizer frequency.

To confirm the locking characteristics of the beat note frequency on the external RF signal, locked beat-note frequencies were measured as a function of the RF synthesizer frequency. The results, shown in Fig. 14, demonstrate that from 3.05 to 11.05 GHz, the beat-note frequency is precisely locked to the RF synthesizer frequency.

Graphic Jump LocationF14 :

RF-synthesizer frequency versus beat-note frequency.

We have developed and demonstrated a simple and versatile system to generate RF signals using optical beat generation. Since the frequency of the generated RF signal, which corresponds to the frequency difference between the two lasers, is locked to the stable external RF signal, it is not necessary to achieve absolute frequency locking of the lasers used in the beat-note generation. In our experiments, the beat-note frequency between the ECL and DFB laser is stabilized within the range 3 to 11 GHz using a delayed RF self-homodyne method combined with the stable reference frequency of the RF synthesizer. The beat-note frequency fluctuation is reduced to 1/20 (short term) and 1/100 (long term) compared with the fluctuation obtained by free running lasers. The proposed system will be applicable to stable and tunable giaghertz frequency range photonic generation of RF signals.

Yao  J., “Microwave photonics,” J. Lightwave Technol.. 27, , 314 –335 (2009). 0733-8724 CrossRef
Kane  T. J., Nilsson  A. C., Byer  R. L., “Frequency stability and offset locking of a laser diode-pumped Nd:YAG monolithic nonplanar ring oscillator,” Opt. Lett.. 12, , 175  (1987). 0146-9592 CrossRef
Day  T., Gustafson  E., Byer  R., “Sub-hertz relative frequency stabilization of two-diode laser-pumped Nd:YAG lasers locked to a Fabry-Perot interferometer,” IEEE J. Quantum Electron.. 28, , 1106 –1117 (1992). 0018-9197 CrossRef
Gianfrani  L. et al., “Offset-frequency locking of extended-cavity diode lasers for precision spectroscopy of water at 1.38  μm,” Opt. Express. 18, , 21851 –21860 (2010). 1094-4087 CrossRef
Bouyer  P. et al., “Microwave signal generation with optical injection locking,” Opt. Lett.. 21, , 1502 –1504 (1996). 0146-9592 CrossRef
Santarelli  G. et al., “Heterodyne optical phase-locking of extended-cavity semiconductor lasers at 9 GHz,” Opt. Commun.. 104, , 339 –344 (1994). 0030-4018 CrossRef
Keitch  B., Thomas  N., Lucas  D., “Injection locking of violet laser diodes with a 3.2 GHz offset frequency for driving Raman transitions in 43 Ca+,” Opt. Lett.. 38, (6 ), 4 –7 (2013). 0146-9592 CrossRef
Komori  K. et al., “Injection-locking of blue laser diodes and its application to the laser cooling of neutral ytterbium atoms,” Jpn. J. Appl. Phys.. 42, , 5059 –5062 (2003). 0021-4922 CrossRef
Liang  W. et al., “Coherent power combination of two master-oscillator-power-amplifier (MOPA) semiconductor lasers using optical phase lock loops,” Opt. Express. 15, (6 ), 3201  (2007). 1094-4087 CrossRef
Gliese  U. et al., “A wideband heterodyne optical phase-locked loop for generation of 3–18 GHz microwave carriers,” IEEE Photonics Technol. Lett.. 4, , 936 –938 (1992). 1041-1135 CrossRef
Biesheuvel  J. et al., “Widely tunable laser frequency offset lock with 30 GHz range and 5 THz offset,” Opt. Express. 21, (12 ), 21 –27 (2013). 1094-4087 CrossRef
Matsuura  S. et al., “A tunable cavity-locked diode laser source for terahertz photomixing,” IEEE Trans. Microwave Theory Tech.. 48, , 380 –387 (2000). 0018-9480 CrossRef
Uehara  T. et al., “Frequency stabilization of two orthogonally polarized external cavity laser diodes using a novel-type optical configuration consist of a phase modulator and a Faraday rotator mirror,” IEICE Electron. Express. 11, (10 ), 20140169  (2014). 1349-2543 CrossRef
Dinovitser  A., Hamilton  M. W., Vincent  R. A., “Stabilized master laser system for differential absorption lidar,” Appl. Opt.. 49, , 3274 –3281 (2010). 0003-6935 CrossRef
Schünemann  U., Engler  H., “Simple scheme for tunable frequency offset locking of two lasers,” Rev. Sci. Instrum.. 70, (1 ), 242 –243 (1999). 0034-6748 CrossRef
Ritt  G. et al., “Laser frequency offset locking using a side of filter technique,” Appl. Phys. B. 79, , 363 –365 (2004). 0946-2171 CrossRef

Tomoyuki Uehara is a research associate at the National Defense Academy of Japan. He received his BS and MS degrees in engineering from Niigata University in 2006 and 2008, respectively, and withdrew from the doctoral program with the completion of course requirements from Kyoto University, Japan. His current research interests include frequency stabilization of lasers. He is a member of SPIE.

Kenichiro Tsuji received his BE, ME, and PhD degrees in engineering from Niigata University, Niigata, Japan, in 1994, 1996, and 1999, respectively. In 1999, he joined the Department of Communications Engineering, National Defense Academy of Japan, where he is currently an associate professor. His current research interests are photonic generation of coded RF signal and fiber-optic sensors based on Brillouin scattering. He is a member of OSA and IEICE.

Kohei Hagiwara is a master’s course student of the National Defense Academy of Japan. He received his BS degree in engineering from the University of Electronic Communication in 2005. The same year, he joined the Japan Maritime Self Defense Force and engaged in duties of procurement, repair, and update for communication apparatus and electronics. He is a student member of IEICE and the Lieutenant Junior Grade.

Noriaki Onodera received his PhD degree from Tohoku University, Sendai, Japan, in 1985. He joined the Department of Communications Engineering, National Defense Academy of Japan in 2001 is and currently a professor. His current research interests include optical generation of microwave signal and its applications. He is a member of the Institute of Electronics, Information and Communication Engineers of Japan, the Japan Society of Applied Physics, the IEEE Photonics Society and Optical Society of America.

© The Authors. Published by SPIE under a Creative Commons Attribution 3.0 Unported License. Distribution or reproduction of this work in whole or in part requires full attribution of the original publication, including its DOI.

Citation

Tomoyuki Uehara ; Kenichiro Tsuji ; Kohei Hagiwara and Noriaki Onodera
"Optical beat-note frequency stabilization between two lasers using a radio frequency interferometer in the gigahertz frequency band", Opt. Eng. 53(12), 124109 (Dec 29, 2014). ; http://dx.doi.org/10.1117/1.OE.53.12.124109


Figures

Graphic Jump LocationF1 :

Schematic of beat-note frequency stabilization by means of a radio frequency (RF) self-homodyne interferometer. PD: photodetector; LPF: low pass filter.

Graphic Jump LocationF2 :

Expermental setup. PD: photodetector; LPF: low pass filter.

Graphic Jump LocationF3 :

Optical spectrum of ECL and DFB laser.

Graphic Jump LocationF4 :

Beat note generated from the two lasers.

Graphic Jump LocationF6 :

Beat note with frequency stabilization.

Graphic Jump LocationF7 :

Beat note without frequency stabilization.

Graphic Jump LocationF8 :

Beat note with frequency stabilization measured by a sampling oscilloscope (2-event averaging).

Graphic Jump LocationF9 :

Beat note with frequency stabilization measured by a sampling oscilloscope (100-event averaging).

Graphic Jump LocationF10 :

Beat note without frequency stabilization measured by a sampling oscilloscope (2-event averaging).

Graphic Jump LocationF11 :

Beat note without frequency stabilization measured by a sampling oscilloscope (100-event averaging).

Graphic Jump LocationF12 :

Beat note between two lasers in frequency stabilization. RF synthesizer frequency set at (a) 3 GHz, (b) 4 GHz, (c) 5 GHz, (d) 6 GHz, (e) 7 GHz, (f) 8 GHz, (g) 9 GHz, (h) 10 GHz, and (i) 11 GHz.

Graphic Jump LocationF13 :

Frequency stability of generated beat note at 10-GHz RF synthesizer frequency.

Graphic Jump LocationF14 :

RF-synthesizer frequency versus beat-note frequency.

Tables

References

Yao  J., “Microwave photonics,” J. Lightwave Technol.. 27, , 314 –335 (2009). 0733-8724 CrossRef
Kane  T. J., Nilsson  A. C., Byer  R. L., “Frequency stability and offset locking of a laser diode-pumped Nd:YAG monolithic nonplanar ring oscillator,” Opt. Lett.. 12, , 175  (1987). 0146-9592 CrossRef
Day  T., Gustafson  E., Byer  R., “Sub-hertz relative frequency stabilization of two-diode laser-pumped Nd:YAG lasers locked to a Fabry-Perot interferometer,” IEEE J. Quantum Electron.. 28, , 1106 –1117 (1992). 0018-9197 CrossRef
Gianfrani  L. et al., “Offset-frequency locking of extended-cavity diode lasers for precision spectroscopy of water at 1.38  μm,” Opt. Express. 18, , 21851 –21860 (2010). 1094-4087 CrossRef
Bouyer  P. et al., “Microwave signal generation with optical injection locking,” Opt. Lett.. 21, , 1502 –1504 (1996). 0146-9592 CrossRef
Santarelli  G. et al., “Heterodyne optical phase-locking of extended-cavity semiconductor lasers at 9 GHz,” Opt. Commun.. 104, , 339 –344 (1994). 0030-4018 CrossRef
Keitch  B., Thomas  N., Lucas  D., “Injection locking of violet laser diodes with a 3.2 GHz offset frequency for driving Raman transitions in 43 Ca+,” Opt. Lett.. 38, (6 ), 4 –7 (2013). 0146-9592 CrossRef
Komori  K. et al., “Injection-locking of blue laser diodes and its application to the laser cooling of neutral ytterbium atoms,” Jpn. J. Appl. Phys.. 42, , 5059 –5062 (2003). 0021-4922 CrossRef
Liang  W. et al., “Coherent power combination of two master-oscillator-power-amplifier (MOPA) semiconductor lasers using optical phase lock loops,” Opt. Express. 15, (6 ), 3201  (2007). 1094-4087 CrossRef
Gliese  U. et al., “A wideband heterodyne optical phase-locked loop for generation of 3–18 GHz microwave carriers,” IEEE Photonics Technol. Lett.. 4, , 936 –938 (1992). 1041-1135 CrossRef
Biesheuvel  J. et al., “Widely tunable laser frequency offset lock with 30 GHz range and 5 THz offset,” Opt. Express. 21, (12 ), 21 –27 (2013). 1094-4087 CrossRef
Matsuura  S. et al., “A tunable cavity-locked diode laser source for terahertz photomixing,” IEEE Trans. Microwave Theory Tech.. 48, , 380 –387 (2000). 0018-9480 CrossRef
Uehara  T. et al., “Frequency stabilization of two orthogonally polarized external cavity laser diodes using a novel-type optical configuration consist of a phase modulator and a Faraday rotator mirror,” IEICE Electron. Express. 11, (10 ), 20140169  (2014). 1349-2543 CrossRef
Dinovitser  A., Hamilton  M. W., Vincent  R. A., “Stabilized master laser system for differential absorption lidar,” Appl. Opt.. 49, , 3274 –3281 (2010). 0003-6935 CrossRef
Schünemann  U., Engler  H., “Simple scheme for tunable frequency offset locking of two lasers,” Rev. Sci. Instrum.. 70, (1 ), 242 –243 (1999). 0034-6748 CrossRef
Ritt  G. et al., “Laser frequency offset locking using a side of filter technique,” Appl. Phys. B. 79, , 363 –365 (2004). 0946-2171 CrossRef

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging & repositioning the boxes below.

Related Book Chapters

Topic Collections

Advertisement
  • Don't have an account?
  • Subscribe to the SPIE Digital Library
  • Create a FREE account to sign up for Digital Library content alerts and gain access to institutional subscriptions remotely.
Access This Article
Sign in or Create a personal account to Buy this article ($20 for members, $25 for non-members).
Access This Proceeding
Sign in or Create a personal account to Buy this article ($15 for members, $18 for non-members).
Access This Chapter

Access to SPIE eBooks is limited to subscribing institutions and is not available as part of a personal subscription. Print or electronic versions of individual SPIE books may be purchased via SPIE.org.