Laser-produced plasma versus laser-assisted discharge plasma: physics and technology of extreme ultraviolet lithography light sources

Guido Schriever; Olivier R. Semprez; Jeroen Jonkers; Masaki Yoshioka; Rolf Apetz

doi:10.1117/1.JMM.11.2.021104

29 May 2012 Laser-produced plasma versus laser-assisted discharge plasma: physics and technology of extreme ultraviolet lithography light sources

Guido Schriever, Olivier R. Semprez, Jeroen Jonkers, Masaki Yoshioka, Rolf Apetz

Author Affiliations +

Journal of Micro/Nanolithography, MEMS, and MOEMS, Vol. 11, Issue 2, 021104 (May 2012). https://doi.org/10.1117/1.JMM.11.2.021104

Abstract

Powerful extreme ultraviolet (EUV) sources at 13.5 nm are a prerequisite for the economical operation of lithography scanners for semi-conductor manufacturing. These sources have been under development for more than 10 years. At the beginning, many source concepts were considered. Compact technologies like dense plasma focus or capillary Z-pinch discharges reached very rapidly fundamental limits as far as power scalability and lifetime were concerned. Other complex technologies-like synchrotrons-eventually dropped out of the race as well, exceeding by far the footprint and cost targets. Over time, the technology solidified toward the two source concepts: on one hand, the discharge produced plasmas (DPP), which eventually led to the development of the current laser-assisted discharge plasma (LDP); on the other hand, the laser-produced plasmas (LPP). All these technologies generate hot and dense plasmas of similar properties, which emit EUV radiations efficiently as a black body radiator or Planck emitter, in a pulsed manner. The plasma generation method, however, is quite different. DPP uses a pulsed high-voltage current discharge to generate plasma heating a gaseous or vaporized material up to temperatures close to 200,000°C. As for LPP, microscopic droplets of molten tin are fired through a vacuum chamber, individually tracked, vaporized by a pre-pulse laser, and eventually irradiated by a pulsed high-power infrared CO2 laser at 50 to 100 kHz, creating a high-temperature tin plasma, which radiates EUV light. In the case of LDP the plasma is generated between two rotating discs. Partially immersed in baths filled with liquid tin, the discs are wetted and covered with a thin layer of liquid tin. A pulsed laser beam focused on one of the discs evaporates a small amount of tin and generates a tin cloud between the two discs. Next a capacitor bank, which is connected to the discs via the liquid tin, discharges and converts the tin cloud into a plasma heated up to 200,000°C as well.

Citation Download Citation

Guido Schriever, Olivier R. Semprez, Jeroen Jonkers, Masaki Yoshioka, and Rolf Apetz "Laser-produced plasma versus laser-assisted discharge plasma: physics and technology of extreme ultraviolet lithography light sources," Journal of Micro/Nanolithography, MEMS, and MOEMS 11(2), 021104 (29 May 2012). https://doi.org/10.1117/1.JMM.11.2.021104

Published: 29 May 2012

ACCESS THE FULL ARTICLE

INSTITUTIONAL
Select your institution to access the SPIE Digital Library.

SELECT YOUR INSTITUTION

PERSONAL
Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.

PERSONAL SIGN IN

No SPIE Account? Create one

PURCHASE THIS CONTENT

SUBSCRIBE TO DIGITAL LIBRARY

50 downloads per 1-year subscription

Members: $195

Non-members: $335 ADD TO CART

25 downloads per 1 - year subscription

Members: $145

Non-members: $250 ADD TO CART

PURCHASE SINGLE ARTICLE

Includes PDF, HTML & Video, when available