This paper presents lithographic performance results obtained from the newest member of ASML's TWINSCAN platform-based step & scan systems, the TWINSCAN XT:1400. The system has been designed to meet the semiconductor industry's aggressive requirements on CD control, overlay and productivity at and below the 65 nm node. This dual stage 193 nm lithographic system combines the worlds highest NA, with excellent overlay and CD control at high throughput on both 200 and 300 mm wafers and is intended for use in volume production environments. Advances in stage technology have enabled further extension of stage scan speeds and an associated increase in tool productivity. However, maximizing the number of yielding die per day also requires stringent overlay and Critical Dimension (CD) control. Tight CD control at improved resolution is supported by the Starlith 1400 projection lens and the extended sigma capabilities of the new AERIAL-E illumination system. Focus control is improved in line with the stringent requirements posed by low-k1 imaging applications, taking full advantage of the unique dual-stage TWINSCAN system architecture.
Rian Rubingh, Youri van Dommelen, Sjef Tempelaars, Marc Boonman, Roger Irwin, Edwin van Donkelaar, Hans Burgers, Guustaaf Savenije, Bert Koek, Michael Thier, Oliver Roempp, Christian Hembd-Soellner
To realize high productivity at the 100-nm node, ASML developed the TWINSCAN™ AT:1100B. This dual-stage 193-nm lithography system combines high throughput TWINSCAN™ technology for 300-mm wafers, excellent dynamical performance, and low-aberration 0.75-NA Starlith™ 1100 projection optics. The system is equipped with a 20-W 4-kHz ArF laser and the AERIAL™ II illuminator, enabling high intensity off-axis and multipole QUASAR™ illumination. Important process control requirements for the 100-nm technology node are CD variation across the chip and across the wafer. Full wafer leveling, including dies on the edge of the wafer, and CD uniformity performance on 300-mm wafers with and without topology are presented, showing full wafer CD uniformity numbers as low as 6.3 nm 3σ for 100-nm isolated lines with assisting features. Imaging performance of dense, fully isolated lines plus dense and isolated contact holes is shown. Also, printing of critical customer structures is discussed. With these results it is demonstrated that the TWINSCAN™ AT:1100B 300-mm ArF Step & Scan system meets the requirements for the 100-nm node.
Rian Rubingh, Youri van Dommelen, Sjef Tempelaars, Marc Boonman, Roger Irwin, Edwin van Donkelaar, Hans Burgers, Guustaaf Savenaije, Bert Koek, Michael Thier, Oliver Roempp, Christian Hembd-Soellner
To realize high productivity at the 100 nm node, ASML developed the TWINSCANTM AT:1100B. This dual stage 193 nm lithography system combines high throughput TWINSCANTM technology for 300 nm wafers, excellent dynamical performance, and low aberration 0.75 NA StarlithTM1100 projection optics. The system is equipped with a 20 W 4 kHz ArF laser and the AERIALTM II illuminator, enabling high intensity off axis and multi-pole QUASARTM illumination. Important process control requirements for the 100 nm technology node are CD variation across the chip and across the wafer. Full wafer leveling, including dies on the edge of the wafer, and CD uniformity performance on 300 mm wafers with and without topology are presented, showing full wafer CD uniformity numbers as low as 6.3 nm 3(sigma) for 100 nm isolated lines with assisting features. Imaging performance of dense, fully isolated lines, plus dense and isolated contact holes is shown. Also printing of critical customer structures is discussed. With these results it is demonstrated that the TWINSCANTM AT:1100B 300 mm ArF Step & Scan system meets the requirements for the 100 nm node.
To meet lithographic requirements for the 130nm generation, the influence of aberrations on printing of various patterns is investigated. This paper shows a process for patterns that are sensitive to coma and three wave. The aberration sensitivities are calculated and the effect on printing experimentally verified. This analysis leads to slight changes in lens adjustment strategy to accommodate the printing of specific DRAM patterns. Additional improvements in materials and surface figures, as well as reduction in process-induced aberrations and associated RMS wave front error, enable the production of tools that are capable of printing the 130nm device generation. The importance of collaboration between makers of lithography tools and their customers cannot be underestimated in finding tool specific limitations. Because of the length of the design cycle of lithography tools it is necessary to perform analysis of device patterns years in advance. The current work also indicates that patterns historically used to determine lens specifications, such as dense and isolated lines, are insufficient to fully determine lens specifications. This paper also outlines techniques that can be used to reduce aberration sensitivities by use of resolution enhancement techniques. This is another area where close interaction between vendor and customer is needed.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.