The Submillimeter Array (SMA) requires precise full-sky blind pointing for its eight 6m antennas, aiming for an error within 3′′, a fraction of the 34′′ FWHM beam at 345 GHz. SMA’s typical 2–3′′ rms pointing accuracy is crucial for efficient array operation, especially with 4 to 6 antenna relocations across 23 pads in various configurations each semester. Traditional calibration using optical guidescopes for mount model errors has shifted to interferometric pointing measurements on quasars, for full model acquisition and baseline calibration. Following every array reconfiguration, mechanical imperfections in antenna mounting lead to significant deviations in azimuth encoder offset and axis tilt parameters, complicating pointing accuracy. To overcome this, a three-layer feed-forward neural network, trained on over ten years of data for each antenna-pad configuration, predicts post-reconfiguration changes. This approach, currently under evaluation and refinement, aims to expedite re-calibration, indicating potential substantial reductions in calibration time and enhanced operational efficiency.
We have fabricated new superconductor-insulator-superconductor (SIS) mixers chips for the 16-element Heterodyne Array Receiver Program (HARP) instrument on the James Clerk Maxwell Telescope (JCMT). The original spare mixer chips were limited and not performed as well as the used ones in HARP. The ability to manufacture new mixer chips would therefore be important for the repair and upgrade of HARP. Our immediate goal is to replace the current nonfunctional mixers in HARP with new chips. We modified the designs of waveguide probe and the matching circuit of the SIS mixer chip. The newly designed chips were fabricated with a quality factor (Rsg/Rn) over 10. The double-sideband (DSB) receiver noise temperature (Trx) is lower than 80K at frequencies between 325 GHz and 375 GHz, which is comparable to the best of the original devices. Three of the sixteen mixers have been replaced and they work very well.
Since the start of full science operations from 2004, the Submillimeter Array has been implementing plans to expand IF bandwidths and upgrade receivers and cryostats. Metal mesh low-pass filters were designed to block infrared (IR) radiation to reduce the thermal load on the cryostats. Filters were fabricated on a quartz wafer through photolithography and coated with anti-reflection (AR) material. The filters were tested from 200 to 400 GHz to verify their passband performances. The measurement results were found to be in good agreement with EM simulation results. They were tested in the far-infrared (FIR) frequency range to verify out-of-band rejection. The IR reflectivity was found to be approximately 70%, which corresponded to the percentage of the area blocked by metal.
The Greenland Telescope project has recently participated in an experiment to image the supermassive black hole shadow at the center of M87 using Very Long Baseline Interferometry technique in April of 2018. The antenna consists of the 12-m ALMA North American prototype antenna that was modified to support two auxiliary side containers and to withstand an extremely cold environment. The telescope is currently at Thule Air Base in Greenland with the long-term goal to move the telescope over the Greenland ice sheet to Summit Station. The GLT currently has a single cryostat which houses three dual polarization receivers that cover 84-96 GHz, 213-243 GHz and 271-377 GHz bands. A hydrogen maser frequency source in conjunction with high frequency synthesizers are used to generate the local oscillator references for the receivers. The intermediate frequency outputs of each receiver cover 4-8 GHz and are heterodyned to baseband for digitization within a set of ROACH-2 units then formatted for recording onto Mark-6 data recorders. A separate set of ROACH-2 units operating in parallel provides the function of auto-correlation for real-time spectral analysis. Due to the stringent instrumental stability requirements for interferometry a diagnostic test system was incorporated into the design. Tying all of the above equipment together is the fiber optic system designed to operate in a low temperature environment and scalable to accommodate a larger distance between the control module and telescope for Summit Station. A report on the progress of the above electronics instrumentation system will be provided.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.